Step Plumbing Guide for Bathtub Installation
Step Plumbing Guide for Bathtub Installation
Blog Article
The author is making several great observations on the subject of How to Install a Bathtub: Install an Acrylic Tub and Tub Surround overall in this post down the page.
Installing a tub isn't specifically rocket science, however it does require strong plumbing, carpentry, and also sometimes, tiling skills. Changing an old tub with a new one is also a reasonably hard job. If the old tub is readily easily accessible, the task can move rapidly; if you have to open a wall surface to eliminate the old tub as well as position the brand-new bathtub, the task is much harder. In either situation, the job is within a house handyman's abilities, although you will certainly require an assistant to leave the old bathtub and also set in the new one. Make certain you have certified yourself for the task as well as fit trying it. As opposed to employing a contractor to take control of a halfway-completed task, it is much better to consider employing one prior to you begin. Possibilities are you may need a specialist plumber to make tube connections.
This post will certainly help you mount a brand-new bath tub in your shower room if you have actually currently purchased a new bathtub and also do not require to transform the plan of your previous water supply pipes.
Your devices as well as product checklist should make up the following:
Removing Old Taps
If you require to change old faucets with new ones as a part of your setup, after that the first thing you must do is disconnect the water system. After doing so, activate the taps to drain any water remaining in the system. The process of removing the existing faucets can be quite bothersome as a result of the limited accessibility that is usually the instance.
Utilize a basin wrench (crowsfoot spanner) or a tap device to undo the nut that connects the supply pipelines to the faucets. Have a fabric prepared for the remaining water that will certainly originate from the pipelines. As soon as the supply pipes have actually been gotten rid of, make use of the exact same device to loosen the nut that holds the faucets onto the bath/basin. You will certainly need to quit the single faucets from turning throughout this process. As soon as the taps have been removed, the holes in the bath/basin will need to be cleaned up of any old sealing substance.
Before going on to fit the brand-new taps, compare the pipeline connections on the old faucets to the brand-new taps. If the old faucets are longer than the new faucets, then a shank adapter is required for the brand-new faucets to fit.
Suitable New Touches
If the tails of the brand-new faucets are plastic, then you will certainly require a plastic adapter to stop damages to the thread. One end of the connector fits on the plastic tail of the faucet as well as the various other end offers a link to the existent supply pipelines.
If you require to fit a monobloc, after that you will certainly require minimizing couplers, which links the 10mm pipe of the monobloc to the typical 15mm supply pipeline.
Next, position the tap in the installing hole in the bath/basin guaranteeing that the washers remain in place in between the faucet and the sink. Secure the faucet in place with the maker supplied backnut. Once the tap is securely in place, the supply pipelines can be linked to the tails of the faucets. The faucets can either be linked by utilizing corrugated copper piping or with typical faucet ports. The former type must be connected to the faucet finishes initially, tightening only by hand. The supply pipes can later be linked to the other end. Tighten both ends with a spanner after both ends have been linked.
Setting up the Tub
Using both wooden boards under its feet, position the tub in the required setting. The wood boards are helpful in equally spreading the weight of the bathtub over the location of the boards rather than concentrating all the weight onto 4 small points.
The following goal is to make certain that the tub is leveled all round. This can be attained by inspecting the level as well as adjusting the feet on the tub till the spirit level reviews degree.
To mount faucets, fit the bottom of the outermost adaptable faucet port to the ideal supply pipeline by making a compression join; after that do the same for the various other faucet.
Turn on the supply of water and also inspect all joints as well as brand-new pipework for leakages and tighten them if needed. Fill up the bath tub and likewise examine the overflow electrical outlet and also the regular electrical outlet for leakages.
Finally, take care of the bathroom paneling as explained in the manufacturer's user's manual. Tiling and also sealing around the bathtub should wait till the tub has actually been made use of a minimum of once as this will resolve it right into its last setting.
Getting ready for the Installation
First of all, the sustaining framework provided with the bath needs to be fitted (if called for) according to the manufacturer's directions. Next, fit the faucets or mixer to the bathtub. When fitting the tap block, it is very important to ensure that if the tap comes with a plastic washing machine, it is fitted between the bath and the taps. On a plastic bath, it is additionally practical to fit a supporting plate under the faucets device to avoid stress on the bathtub.
Fit the flexible faucet ports to the bottom of the two taps utilizing 2 nuts and also olives (often provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the outlet via the hole in the bath. Make use of the nut supplied by the manufacturer to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the versatile overflow pipe to the overflow electrical outlet. After that, screw the pipe to the overflow face which must be fitted inside the bathroom. Ensure you utilize all of the provided washers.
Connect the catch to the bottom of the waste outlet on the tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and screw on the trap to the outlet. Connect all-time low of the overflow tube in a similar manner.The bath must currently be ready to be suited its last position.
Tiling Around the Bathtub
In the area where the bathroom meets the tile, it is required to seal the accompanies a silicone rubber caulking. This is very important as the fitting can move sufficient to fracture a rigid seal, creating the water to permeate the wall between the bathroom as well as the tiling, causing issues with moisture and also feasible leaks to the ceiling listed below.
You can pick from a range of coloured sealants to assimilate your components and fittings. They are offered in tubes as well as cartridges, and are capable of securing gaps up to a size of 3mm (1/8 inch). If you have a bigger space to load, you can fill it with twists of soaked paper or soft rope. Bear in mind to always fill the bathtub with water before sealing, to allow for the motion experienced when the tub remains in usage. The sealer can fracture rather very early if you do not think about this activity before sealing.
Alternatively, ceramic coving or quadrant floor tiles can be made use of to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are additionally easily readily available on the marketplace. It is suggested to fit the ceramic tiles utilizing waterproof or waterproof sticky as well as cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
We hope you enjoyed reading our article about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround. Thank you for spending some time to read through our piece of content. Liked our blog? Please share it. Let somebody else locate it. Many thanks for your time. Kindly pay a visit to our website back soon.
24/7 plumbers for emergencies. Report this page